Robe Color Wash 575E AT Spezifikationen PDF herunterladen (Seite 25)

chapter “DMX protocol” for detail description.

Lamp Presetting --- Select this menu to change the lamp “behaviour”.

Lamp On/Power On --- Select this function to turn the lamp on automatically after switching

the xture on.

Lamp Off via DMX --- Select this function to switch off the lamp via DMX.

Lamp On if DMX Present --- This function allows you to strike the lamp automatically after

26 seconds if DMX signal is present on the data link.If the ignition is unsuccessfull (e.g.lamp

is too hot),the xture will try to ignite the lamp after next 26 s.This process will repeat until

the lamp lights.

Lamp Off if not DMX --- This function allows you to switch Off the lamp automatically after 2

minutes if DMX signal is missing on the data link.

Lamp Ignition Delay --- This function allows you to set the time delay( 0-90s) before the

lamp will be ignited.This setting will not affect starting the lamp direct from the control panel

(menu “Lamp On/Off”).

Lamp Low Power Delay

This function enables set the time period after that the

lamp power will be reduced if the shutter/dimmer is closed.The delay time can be set up to

600seconds.Default setting is10s.

Lamp Light Sensor --- Select this function to switch the lamp light sensor on or off.The option”On” is for the

standard operation.

Important: The option”Off” is for “emergency operation” only if the lamp light sensor is defective and you will wait

for a service intervertion! If the lamp light sensor is switched off and at switching the lamp on the electronics

will still try to ignite the lamp until it shines (even when the lamp is damaged or absent), on this account some

electronics parts could be damaged!

Display Adjusting --- This function allows you to change the display settings.

Display Permanent On --- This function allows you to keep the display on or to turn off

automatically 2 minutes after last pressing any button on the control panel.

Display Intensity --- Select this function to adjust the display intensity (1-min.,10-max.).

Display Backlight --- Select this function to adjust the display backlight (1-min.,10-max.).

Display Turned --- Select this function to turn the display by 180°.

Blackout d.M.C. --- Select this function to enable the blackout during the head movement correction (if the

moving head lost its right pan/tilt position for a short moment) .

Pan/Tilt Feedback --- This function allows to return the mowing head to the required pan/tilt position after

changing the position by external force (e.g.by stroke).

Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the xture can be

demaged!

Note: If the feedback was switched off ,the pan/tilt-position is changed by an external force and the feedback

is switched on again,the moving head might not to be synchronized with the DMX signal.You have to make a

reset in order to synchronize the moving head with the DMX signal.

Microphone Sensitivity --- Select this function to adjust the microphone sensitivity from 1(maximum) to 20(mi-

nimum).If the sensitivity is correctly adjusted,the mark will appear (blinking in the bass beat.)

Fan Modes --- By using this function you can choose 2 types of the fan speed operating modes.

Auto Cooling --- The fans automatically raise their speed in order to control inside tempera-

ture of the lighting, if the temperature inside increases about certain level (the low fan speed

reduces the cooling of the lighting). This cycle can repeat several times until the temperature

inside is on a suitable level.

High Cooling --- The cooling fans work on max. speed (max. cooling).This mode we re-

commend for high ambient temperature (30 °C and more).

Pan/Tilt mode --- Use this menu to set the character of the pan/tilt movement.

Time mode --- Pan and tilt will move with different speeds and they will come at the same

time to end point (pan and tilt sets its optimal speed).

Speed Mode --- Pan and tilt will move with the same speed as adjusted by the channel 5

(Pan/Tilt speed).E.g. pan will come to the end point and wait for tilt,which has longer track.

Active Blackout while: --- Use this function if you wish to close the light output during effect changes.

Pan/Tilt Moving --- This function closes the light output during pan/tilt changes.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 34 35

Kommentare zu diesen Handbüchern

Keine Kommentare

Robe Color Wash 575E AT Spezifikationen Seite 25

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Flutlichter Robe Color Wash 575E AT