Robe Color Wash 575E AT Spezifikationen PDF herunterladen (Seite 18)

6. Controller mode

The xtures are individually addressed on a data link and connected to the controller.The xtures respond to

the DMX signal from the controller.

6.1 DMX addressing

The control panel on the front panel of the xture allows you to assign the DMX xture address, which is dened

as the rst channel from which the ColorWash 575E AT will respond to the controller.

If you set, for example, the address to channel 23, the ColorWash 575E AT will use the channel 23 to 44 for

control (if mode 1 is selected).

Please, be sure that you don’t have any overlapping channels in order to control each ColorWash 575E AT

correctly and independently from any other xture on the DMX data link.

If two, three or more ColorWash 575E AT are addressed similarly, they will work similarly.

For address setting, please refer to the instructions under "Fixture Address".

Controlling:

After having addressed all ColorWash 575E AT , you may now start operating these via your lighting control-

ler.

Note:After switching it on, the ColorWash 575E AT will automatically detect whether DMX 512 data is received

or not.If there is no data received at the DMX-input, the display will start to ash "A001" with actually set ad-

dress.

This situation can occur if:

- the 3 PIN (5pin) XLR plug (cable with DMX signal from controller) is not connected with the input of the Color-

Wash 575E AT

- the controller is switched off or defective, the cable or connector is defective or the signal wires are swap in

the input connector.

Note:It’s necessary to insert the XLR termination plug (with 120 Ohm) to the last xture in the link in order to

ensure proper transmission on the DMX data link.

6.2 Remotely controllable functions

Lamp

The ColorWash 575E AT is to be operated with a Philips MSR 575/2 lamp.

A relay inside of the ColorWash 575E AT allows you to switch on and off the lamp via the control panel or via

your DMX-controller without affecting the rest of the lighting.

To switch On/Off the lamp, please refer to "Lamp On/Off ".

Note:It is also important to note, that the discharge lamp is cold restrike types, that means, that they have to be

cold before re-striking. For this reason, you have to wait 5 minutes (max. speed of fan must be adjusted) after

having switched Off the lamp before you can switch it back On again. If you try to switch On the lamp within 5

minutes after having switched it Off, the ColorWash 575E AT will store this information and automatically ignite

the lamp when the 5 minutes period has expired.If the ignition of the lamp is seven times unsuccessful, on the

display will appear "Lamp Error", meaning that the lamp could be damaged or even missed, or there could

be a failure on the ignitor or ballast.

Colour wheel

This wheel contains 5 replaceable 'SLOT&LOCK' dichroic lters + open.The colour-wheel can be positioned

between two adjacent colours in any position. It is also possible to rotate the colour wheel continuously at dif-

ferent speeds ("Rainbow effect“ in both directions).

Effect wheel

This wheel contains a frost lter and a rotating indexable beam shaper.

Zoom

Motorized zoom unit enables zoom between 12° and 34° beam angle.

Dimmer/Shutter/Strobe

Smooth 0 - 100 % dimming is provided by the combined mechanical dimmer/shutter unit. This unit may also

be used for strobe effect.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 34 35

Kommentare zu diesen Handbüchern

Keine Kommentare

Robe Color Wash 575E AT Spezifikationen Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Flutlichter Robe Color Wash 575E AT