1 Version 1.5
104.8 Rigging the xtureDANGER TO LIFE! Please consider the respective national norms during the installation! The installation must only be carried
11For overhead use, always install a safety-rope that can hold at least 10 times the weight of the xture. You must only use safety-ropes with screw-o
124.9 DMX-512 connectionThe xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired inparallel.Only u
134.10 Ethernet connectionThe xtures on a data link are connected to the Ethernet with Art-Net communication protocol.The controlling software from P
14Ethernet / DMX operationOptions “Ethernet/DMX” has to be selected from “Set Ethernet Mode” menu on the rst xture (connected to the network) in the
155. ColorWash 575E AT-DMX Protocol-version 1.0 Mode/ChannelValue FunctionType of control1 2 3 41 1 1 1 0 - 255PanPan movement by 530°proportional2
16 Mode/ChannelValue FunctionType of control1 2 3 47 7 9 9021436485107128-129130-141142-153154-165166-177178-189190 - 215216 - 217218 - 243244 - 24925
17 Mode/ChannelValue FunctionType of control1 2 3 414 13 16 15184-191192-199200 - 207208 - 215216 - 223224 - 231232 - 239240 - 243244 - 249250 - 255M
186. Controller mode The xtures are individually addressed on a data link and connected to the controller.The xtures respond to the DMX signal fr
197.Control menu mapDefault settings=Bold print Default settings=Bold print Fixture Address DMX Address 001 : 512 Ethernet
2Table of contents1. Safety instructions ... 32.
20 Personality User Mode User A Settings User B Settings User C Settings DMX Presetting Mode 1 Ch.1
21Lamp On/Off (On,Off) Test sequences Mode 1 Pan (0-255) Tilt (0-255) Zoom (0-255) Run Test Program Mode 2 M
22 Effect Adjustment DMX Values Pan (0-255) : Dimmer ne (0-255) Calibrate Values
238. Control menu The control panel situated on the front panel of the base offers several features. You can simply set the DMX address, read the numb
24 Resetable Hours - The function shows the number of the operation hours with the lamp on that the ColorWash 575E AT has been powered on since
25chapter “DMX protocol” for detail description. Lamp Presetting --- Select this menu to change the lamp “behaviour”. Lamp On/Power On --- Select
26 Colour Wheel Moving --- This function closes the light output during colour wheel 1/wheel 2 changes.IR Sensor --- Select this function to
27program and the 3 free programs,each up to 99 steps.Each program step has a step time.Step time-the time,during which effects last in the current s
28List of the calibrated effects: Colour Wheel Zoom Effect wheel Dimmer Effect Indexing 2. Calibration via the DMX
29without taking it out from the case.To enter “Power down mode”:Press and hold [ENTER] and at the same time switch on the Power switch.The following
3CAUTION!Keep this device away from rain and moisture!Unplug mains lead before opening the housing!FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL C
30 value PARAMETER_DATA=0x84 - lamp OFF by DMX value on DMX channel value PARAMETER_DATA=0x88 - lamp OFF if DMX is not present2...Commands r
31Colour Wheel Error 1 (Colour Wheel Error 2 )The messsages will appear after the reset of the colour wheel if this wheel is not located in the defa
32CMY-colours mixing module: - Smooth CMY colour mixing system - Colour temperature correction lter lowers the colour temperature from 7200K to
33Beampath: Standard Fresnel lens+standard zoom lens: Weight: 28 kg Dimensions(mm):Dimensions of the xture:
34Dimensions of top heats:13. Maintenance and cleaning It is absolutely essential that the xture is kept clean and that dust, dirt and smoke-uid res
42.Operating determinationsThis device is a moving-head for creating decorative effects and was designed for indoor use only.If the device has been e
53. Description of the device1 - Front lens2 - Moving head3 - Yoke4 - BaseRear panel of the base:1 - 5-pin DMX output2 - 5-pin DMX input 3 - 3-pin DMX
64. Installation4.1Fitting the lampDANGER !Install the lamps with the device switched off only.Unplug from mains before !To insert the lamp loosen th
74.3 Inserting/Exchanging colours DANGER!Install the colours with the device switched off only.Unplug from mains before!If you wish to change colours
84.5 Changing the front and zoom lenses The ColorWash 575E AT is supplied with one type of the front lense(Fresnel lens) and one type of the zoom lens
94.6 Connection to the mainsVerify the power supply settings before applying power!If you wish to change the power supply settings,see the chapter bel
Kommentare zu diesen Handbüchern