Robe Color mix 575 AT Spezifikationen PDF herunterladen (Seite 25)

2. Press [UP] or [DOWN] to select the desired xture ("MASt." - "SLA.9") and press [ENTER]-button.

3. Press [UP] or [DOWN] to select the desired program step ("St.01" - "St.99") and press [ENTER]-button.

4 Press [UP] or [DOWN] to select the desired item and press [ENTER]-button.Now you can edit by [UP] or [DOWN] buttons the DMX

value (0-255) for selected item:

P.End. - a total number of the program steps (value 1-99).This value you must set before start

programming(e.g. if you want to create program with the 10 steps,set P.End=10).

Colo. a colour wheel C.SPd. a CMY/dimmer speed

Col.F. a colour ne EFFE. an effect wheel

CYAN cyan lamellas Zoom a zoom

MAGE. magenta lemellas Stro. a strobe/shutter

YELL. yellow lamelas dimr a dimmer

Macr. CMY macros

S.tim. a step time,value 0,1-25,5 seconds

COPY.- copying the current prog. step to the next prog. step .If the last prog.step is copied to the

next prog. step ,parameter "P.End" is increased about one by itself (except step 99).

5. Press [ENTER]-button to conrm adjusted value .

6. Press [MODE]-button,select next prog. step and repeat this procedure (steps 4 - 6).

9.9 Reset functions

This option enables the ColorMix 757 AT to index all effects (functions) and return to their standard positions.

9.10 Special functions

Use this menu for special services like adjusting lamp or adjusting effects.

LA.Ad. --- Lamp adjustment.This function can be used when you make the ne adjustment of the lamp.If you select this function,all

effects will be canceled,shutter will be opened and the dimmer intensity will be set onto 100%.By using the option "Zoom" you can

set the light level on the at surface (wall) and perform the ne lamp adjustment.

CodE --- Code.This function contains identication hexadecimal code (0000-FFFF) for the xture, which is used for the master/slave

operation.

AdJ. --- Effect adjustment.By this function you can calibrate and adjust the effects to their standard/right positions.Disconect the

DMX controller from the xture and select "AdJ." menu.The display shows step by step effects by which you can adjust the xture to

the required position before the function calibration(DMX controller must be disconnected) . When the positioning is nished ,select

"F.CAL." and press [ENTER]:

1. Calibration via the control board

Disconnect DMX controller from the xture.Press [ENTER] and use [UP] and [DOWN] in order to display the following items: "Colo

,CYAn,MAGE,YELL,EFFE,Zoom,dimr" for very smooth function calibration. Select one of them, press [ENTER] and use the

[UP] and [DOWN] in order to adjust their right value from 0 to 255. Then press [ENTER] to conrm or [MODE] to cancel and return to

the menu. This can be repeated for each calibration parameter if it is required. When the calibration is nished, it is necessary to use

the "A.rES" function in order to write the calibration values to the memory (EPROM) and to make a reset in order to check the newly

adjusted positions of the colour, gobo wheels and dimmer. When the reset of the xture is nished, the display will show the "F.CAL"

message. Press [ENTER] to repeat the calibration or [MODE] to return to the "AdJ." menu.

2. Calibration via the external controller

Connect the DMX controller to the xture, press [ENTER] and the [UP] and [DOWN] buttons in order to display the following items:

"Colo,CYAn,MAGE,YELL,EFFE,Zoom,dimr" . Select one of them and press [ENTER].

Now you can calibrate this effect by your controller. The DMX calibration protocol is described in the table mentioned below.

DMX calibration protocols:

Effect Mode 1 Mode 2

"Colo."- Colour wheel channel 15 channel 12

"CYAn"- Cyan channel 16 channel 13

"MAGE."-Magenta channel 17 channel 14

"YELL."- Yellow channel 18 channel 15

"EFFE." - Effect wheel channel 19 channel 16

"Zoom"-Zoom channel 20 channel 17

"dimr"- Dimmer channel 21 channel 18

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 31

Kommentare zu diesen Handbüchern

Keine Kommentare

Robe Color mix 575 AT Spezifikationen Seite 25

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Flutlichter Robe Color mix 575 AT